MVQUICKR
Battery Hot Swap system for RED ONE®
Specifications:
- Nominal Voltage: 14.8V
- Voltage range: 10.8V ~ 16.8V
- Nominal Capacity: 1.5Ah, 21Wh
- Max. discharge current: 10A
- About up to 12~15 minutes runtime when used standalone as an UPS backup battery
- Installable on QUICKPLATE, replace the original battery plate
- Self charging through the installed battery, can be charged with a separate charging unit
- Allow data communication from battery to camera supporting the original data bus
- Size: 142 x 83 x 50mm (5.59" x 3.27" x 1.97")
- Weight: 0.49Kg (1.08lbs)
- NEW: enhanced contact protection for safer air transport
Description
MVQUICKR is a hot-swapping interface, with the same features of MVQUICK, to be installed permanently on the existing QUICKPLATE instead of the standard battery mount.
The main purpose of this device is to allow battery replacement without power interruption to the camera through an automatic detection of the battery removal.
Best used with BLUESHAPE V-lock batteries, it support the original digital communication bus from battery to camera allowing direct communication of the runtime parameters to the LCD and viewfinder.
Additionally, MVQUICKR provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements.
High-load cell technology permits discharging of up to 10A when used as a stand alone power source.
Although the internal battery is recharged with every installation of a fresh V-lock battery pack, a separate charging unit has been provided to allow for fast and full charge when the unit is empty.
In the box:
1x MVQUICKR
1x ACDC Charging Unit
1x Screw set
A recent addition is the CONTACT COVER (shown here) that we started including on every V-mount battery that comes out of our production as the ultimate protection against short circuit of the contacts.
This cover does exactly what it says and makes it virtually impossible for a short between the terminals to occur during transport. This is our latest enhancement in our list of safety features that give maximum protection, especially important during air transport.
We request our clients to store the original boxes and also the CONTACT COVERS so as to reuse them if our batteries need to be transported in any aircraft.
The main purpose of this device is to allow battery replacement without power interruption to the camera through an automatic detection of the battery removal.
Best used with BLUESHAPE V-lock batteries, it support the original digital communication bus from battery to camera allowing direct communication of the runtime parameters to the LCD and viewfinder.
Additionally, MVQUICKR provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements.
Principle of operations
Installation
MVQUICKR is permanently installed on QUICKPLATE as an interface between the battery and the camera.
During normal operation, the battery powers the camera and MVQUICKR monitors the battery for an immediate takeover in case of need.
During normal operation, the battery powers the camera and MVQUICKR monitors the battery for an immediate takeover in case of need.
Battery removal
When the battery is removed or when it becomes empty (with voltage below 13V) MVQUICKR provides instantaneous power to the camera without any interruption.
As soon as MVQUICKR starts to operate, the LEDs light up indicating the state of the available internal power.
As soon as MVQUICKR starts to operate, the LEDs light up indicating the state of the available internal power.
Usage as independent power source
In case of emergency, MVQUICKR can even be used as a stand alone power source (21Wh available when fully charged).
It can provide around 12~15 minutes of further runtime.
During all this time the LEDs remain lit.
It can provide around 12~15 minutes of further runtime.
During all this time the LEDs remain lit.
Battery reinstallation
When a new battery is installed (with battery voltage > 14V), MVQUICKR turns off automatically leaving the battery to power the device.
The energy lost by MVQUICKR to sustain the camera during the battery swap operation is automatically and silently replenished from the fresh battery without affecting the operation. This process allows unlimited hot-swap operations and practically a continuous power source. In case of need, MVQUICKR can be quickly charged with the provided charger unit.
The energy lost by MVQUICKR to sustain the camera during the battery swap operation is automatically and silently replenished from the fresh battery without affecting the operation. This process allows unlimited hot-swap operations and practically a continuous power source. In case of need, MVQUICKR can be quickly charged with the provided charger unit.
High-load cell technology permits discharging of up to 10A when used as a stand alone power source.
Although the internal battery is recharged with every installation of a fresh V-lock battery pack, a separate charging unit has been provided to allow for fast and full charge when the unit is empty.
In the box:
1x MVQUICKR
1x ACDC Charging Unit
1x Screw set
A safer little detail
We care and strongly respect the IATA requirements when it comes to transporting batteries. Towards this, we have adopted high quality individual packaging for every individual battery.A recent addition is the CONTACT COVER (shown here) that we started including on every V-mount battery that comes out of our production as the ultimate protection against short circuit of the contacts.
This cover does exactly what it says and makes it virtually impossible for a short between the terminals to occur during transport. This is our latest enhancement in our list of safety features that give maximum protection, especially important during air transport.
We request our clients to store the original boxes and also the CONTACT COVERS so as to reuse them if our batteries need to be transported in any aircraft.
Details
 |
LED indicators showing state of charge of internal battery |
 |
Push button for capacity check |
 |
Charging socket. Plug the charger here to apply the first full charge session |
 |
Installation interface for external V-Lock battery |
 |
Push-pull output connector |
 |
D-Tap auxiliary connector |
 |
Screw pattern for installation on QUICKPLATE |
Gallery
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
MVQUICKR
Videos
January 2011
Quick Changer the battery Hot-Swap adapter
MVQUICK is a hot swap system to be installed as a battery interface between the camera (or any other V-Lock compatible device) and the battery pack. The main purpose is to allow camera battery replacement without any power interruption through an automatic detection of the battery removal.
Additionally, MVQUICK provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements.
MVQUICK is designed to work perfectly even with RED® ONE cameras.
Other models are available to fit different cameras.
Downloads
Certifications
 MVQUICKR CE Certificate - Version:1.0 (359.95 KB) |
CE certificate of conformity for MVQUICKR |
| MVQUICKR Transport Certificate - Version:1.0 (692.92 KB) |
UN38.3 IATA Transport declaration for MVQUICKR |
| MSDS - Version:1.2 (65.0 KB) |
Material Safety Data Sheet for batteries |
Application Notes
| IATA Li-Ion Air Transport guide - Version:2014 (121.94 KB) |
2014 update of the IATA air transport regulations for rechargeable lithium ion, with a dedicated focus on BLUESHAPE batteries range |
